Installing the Servo-controlled Lift
To install the servo-controlled lifting and lowering mechanism on your Redcat Coe Hauler, you will need a little kit that includes two servos and a Y controller. The servos in this kit work together to lift and lower the vehicle. You can purchase this kit for around $50, but if you already have some spare servos lying around, you can use those instead. The links needed for the installation are already included with your Redcat Coe Hauler, so there’s no need to purchase any additional parts. It is essential that the servos you use are strong enough to lift the vehicle and its load effectively.
Setting Up Endpoints
Once you have installed the servo-controlled lift, it is critical to properly set up the endpoints on the radio. This step ensures that the servos do not experience unnecessary stress when lifting and lowering the vehicle. By correctly configuring the endpoints, you can prevent any damage to the servos and maintain smooth operation.
Increasing the Lift with Proper Servos
One common drawback of the Redcat Coe Hauler is its limited ground clearance, which restricts its ability to handle uneven surfaces. However, there is a super cool modification you can make to overcome this limitation. By using the proper servos in combination with your radio controller, you can increase the lift of the vehicle by 3 inches.
Setting up the Servo Lift
To set up the servo lift on the Redcat Coe Hauler, you will need to follow a few simple steps. Firstly, it is recommended to adjust the lift height to about half an inch. The manufacturer suggests a weight of 35 kg for this task.
Removing the Placeholders
Before installing the servo lift, you will need to remove the dummy placeholders that are currently in place. These placeholders are temporary and will be replaced by the servos. This is where the uniqueness of the Redcat Coe Hauler system comes into play.
The Role of the Rods
The Redcat Coe Hauler system utilizes rods to hold the elevation of the vehicle. These rods work in conjunction with the servo arm to keep the vehicle in place. When the rods are completely horizontal and facing each other, the force is canceled out. This means there is no load on the servo or the arm in this position, which is the normal cruising position.
Installing and Adjusting the Servo Lift
Once the placeholders have been removed, you can proceed to install the servos. Place the servo in the designated position and secure it. Next, attach the servo arm provided by the manufacturer.
Lowering the Vehicle
With the servo lift properly set up, you can now lower the vehicle. It may seem higher than normal initially, but this is part of the process. However, it is crucial that the bumpers and chassis of the vehicle touch the ground in this position. The servos are currently holding the entire weight of the vehicle, which can cause stress and heat up the servos. Resting on the ground helps alleviate this pressure.
Setting the Endpoints
To ensure optimal performance, it is important to set the endpoints of the servo lift using the radio controller. This might seem challenging without any labeling, but the Redcat Coe Hauler radio offers a simple solution. Look for the endpoint buttons and trim on the controller. These buttons allow you to adjust and fine-tune the endpoints of the servo lift.
By following these steps, you can set up the servo lift and endpoints on your Redcat Coe Hauler effectively. Enjoy the benefits of this unique system that allows you to adjust the elevation of your vehicle with ease.
Setting Up Servo Lift
To set up the servo lift on the Redcat Coe Hauler, follow these steps:
1. Trim on the Steering Wheel
Begin by setting the trim on the steering wheel. You will be able to see the movement of the trim as you adjust it. Remember that the last position you set will determine the end point of the servo lift.
2. Setting End Points of Different Channels
To set the end points of the different channels, press the bind button twice, performing a quick double-click. This action will change the channel you are controlling. For example, if you want to control the throttle (channel two), you will see the flashing twice after the double click. Any trim adjustments or end point settings you make will now affect the throttle.
3. Controlling Toggle Switch
If you have a toggle switch on your Redcat Coe Hauler, you can use it to control a specific channel. Press the bind button again to change the controlled channel. For instance, if you are not using the toggle switch and want to control Channel 4, perform the double click once more. The flashing four times indicates that you are now controlling the trim and end points of Channel 4.
Adjusting Servo Lift and End Points
4. Adjusting Height
To adjust the height of the vehicle, press the corresponding button or switch on your transmitter. In this case, the height is increased by pressing the button. You may need to press it multiple times to achieve the desired height. Keep in mind that this elevated position is not meant for driving, but rather for situations where you may want to park with the radio on.
5. Checking the Lift
To check the lift of your Redcat Coe Hauler, utilize the three-position switch. This switch allows you to control and adjust the lift to different levels. Experiment with each position of the switch to see how it affects the lift of your vehicle. This feature provides flexibility and variability in your driving experience.
By following these steps, you can successfully set up the servo lift and end points on your Redcat Coe Hauler. Take your time to adjust the settings to suit your preferences and maximize your control over the vehicle. Enjoy the enhanced versatility and performance that this feature brings to your RC experience.
Setting Up Servo Lift
To begin setting up the servo lift for your Redcat Coe Hauler, there are a few important steps to follow. Firstly, it’s essential to understand that driving with the lift engaged is not recommended as it puts strain on the servo. Therefore, the lift is primarily for display purposes.
To start, position the lift at its end point, ensuring that it is horizontal. This is crucial as it allows for the cancelation of forces and ensures optimal performance. Adjust the endpoints of the lift to ensure they are also horizontal.
It’s worth noting that the strength of the servos you have plays a significant role. In this case, powerful 4S servos are being used, which have a capacity of around 800 to 1000. These servos should be more than capable of handling the weight of the lift. However, it’s important to keep in mind that the lift’s capacity is determined by the length of the servo arm.
Choosing the Right Servo Arm
Selecting the appropriate servo arm for your Redcat Coe Hauler is vital to ensure optimal performance and strength. Consider using an Amazon special servo arm, which is cost-effective and readily available. These servo arms can be reinforced by utilizing a double shear method, placing one on each end. This additional reinforcement increases the overall strength of the lift.
Testing the Lift’s Strength
Once the servo lift and endpoints are set up correctly, it’s time to test the lift’s strength. To do this, load the bed of the Coe Hauler with a weight that you intend to lift. The powerful 4S servos should be more than capable of handling the weight, given the proper setup.
By following these steps and using the right components, you can ensure that your Redcat Coe Hauler’s servo lift is properly set up and optimized for its intended use. With a sturdy lift in place, you can confidently lift and transport items with ease.
Setting up the Servo Lift
When it comes to enhancing the functionality of your Redcat Coe Hauler, one of the key upgrades you can consider is setting up a servo lift system. This modification will not only allow you to drive on different terrains but also give your vehicle a realistic hydraulic-like lowering and increasing effect. In this article, we will guide you through the process of setting up the servo lift and adjusting the endpoints for optimal performance.
Ensuring Proper Functionality
Before diving into the setup process, it’s important to ensure that your Coe Hauler is equipped with the necessary components to handle the added power. By upgrading to a more powerful motor, you’ll be able to haul heavier loads and achieve greater speed than the standard three miles per hour. Additionally, it’s crucial to verify that the temperature of your vehicle’s components, particularly the servos, doesn’t exceed safe levels. Excessive heat can impact the performance and lifespan of your components.
Changing the Radio
To effectively control the speed of the servos and achieve the desired smoothness in movement, changing the radio system is essential. The jerky movements experienced with the default setup can be addressed by opting for a radio that offers precise control over servo speed. By having the ability to set the speed to a slower, more controlled rate, you can mimic the behavior of a hydraulic lift, complete with gradual lowering and raising actions.
Adjusting Servo Endpoints
Setting up the servo lift also involves adjusting the endpoints to ensure the lift operates within the desired range. By utilizing endpoint adjustments, you can limit the travel distance of the servo, preventing it from exceeding the boundaries set by your lift system. This is particularly important to avoid overextending the servo and causing damage or strain to the lift mechanism.
Enhancing the Experience
To truly maximize the potential of your Coe Hauler and elevate your driving experience, consider adding small additional features. By incorporating sound effects that mimic hydraulic operations, you can further enhance the realistic appeal of your vehicle. These subtle touches can truly make a difference in immersing yourself in the joy of controlling your Redcat Coe Hauler.
In , setting up a servo lift system on your Redcat Coe Hauler can greatly enhance its functionality and realism. By upgrading the motor, changing the radio system, and adjusting the servo endpoints, you can achieve a more controlled and smooth lift motion. Additionally, adding small touches like sound effects can significantly contribute to an immersive experience. So, get ready to take your Coe Hauler to the next level and unlock its full potential. Happy driving!
By following the steps outlined above, you can successfully install and set up the servo-controlled lift on your Redcat Coe Hauler. This modification not only increases the vehicle’s functionality but also ensures that the servos are properly utilized without being subjected to unnecessary stress. With this modification, you can easily navigate obstacles and uneven terrain, enhancing your overall driving experience with the Redcat Coe Hauler.