The transmitter i use is this: one is the devil’s 7e and if we turn it on, i use the version 5.0 and i believe that’s. The latest version that they have so after you have everything wired up as per the wiring diagram that i have here now install the battery and turn it on and the blinking light shows you that it has power. We can go ahead and turn on our transmitter, and now this one i’ve already got it bounded and i’ve already got it set to the controls that i like. So let me try to see if i could choose a different uh go into choosing a different model, because this one is is already binded it’s already set to the correct channels that i, like let’s, do model setup i’m, just pressing ent for enter. So we can load a different model model 16. Has none come down here to the Music protocols and change it to uh dsm ii? Now you can go over to bind it bound it again, and now all of these controls are set differently. Now the left stick is for the servo and motor and the right stick are for the lights now. All i have to do now is change. The right stick to be my throttle for the motor up and down and left and right to be the servo. Instead of the motor and these switches up here, f mode, f, mod and hold will be changed to the lights and just on the side note normally, when the receiver is not bounded.
Yet you will see the light flash really fast and that will indicate that it’s not bounded to anything yet so from here. Normalt, what i like to do is go into the menu click enter and then go into the transmitter menu and then go down to channel. Monitor here you can see where your sticks are channel, one is left, stick up and down. So what i normally do is i just write. It here, left side right side and then the up and down stick channel one and in channel two i meant channel 4. Would be the left? Stick you can see it indicated by the numbers. Kanal 4 is the left, stick left and right so left and right channel four, and then the right stick up and down channel three, and this will be channel two. I also need to mention that we only know the channels if you click, Jeg vil gerne sige, enter or no this button to go forward. You could actually see uh the names of each channel. So if we go, the left, stick up and down will be throttle and normally what i would do is i would write that here and then the left and right stick is rudder, and now the right stick up and down is the elevators. And now this will be our aileron. This is aileron here, Højre, stick left and right now, with these with these written down like this, we want to or actually what i want to do.
Is i like to change this channel 4. This channel 4 is left and right stick to be my my servo, so on my left, stick the left and right uh channel 4. I want it to be my servo and then the right stick up and down. I want that to be my throttle, which is channel three or i’m sorry, the motor. So now that we have those channel written down, we can go and change the output of the sticks to our liking. So we can just exit out of here and then go to Music model menu go down to the mixer, and here in this mixer we can change the channels to our liking. The last piece of information that needs to be written down is where each of these either the motor servo and the lights are, are which channel they are on. So if we go through each of them, one by one, you can hear left and right. Our left and right stick is for the motor, so the left and right stick, which is on channel 4. This is motor, so that means that the motor is on the rudder channel and our up and down. Stick is the throttle, which means that the servo is on the throttle channel and our lights are on the aileron and uh the elevator channel. So now what we can do is we can go into the menu and we can start changing these to our liking, and you can do this.
Men, you can set the channels to whichever stick you want and you can set either the servo or motor on whichever stick you want, but my preference is having the throttle on the right stick and my steering on the lift stick. So we go into a model menu and then we go down to mixer. Here we have throttle, which is our stock configuration which will be set to to throttle, and we have here saying that the throttle is the our servo. Our throttle is our servo okay, and we want it to be on the on channel four. Faktisk, what i want to do is change the change, the lights, which will be on channel two and three change the lights over to these two switches up here. First and then i can change the the motor and the servo around. So if i go in here to simple and click enter, i could change this over to uh the source. I can change the source over to either hold or f mode. I could just i’ll just put that down to hold, og nu, if i use the switch, you can see the light come on and let’s do the same for uh channel 3.. Since the we’ve already used this for the front lights, we can use f mode for the rear lights, so we change this to f mode. Save the rear lights will come on now. What i want to do is go back to this menu here.
I want to change the motor over to the right stick up and down so here. If we remember the motor is on the rudder channel, which is channel channel 4 down here, but it is the rudder channel. What we can do is we can go down here and say: hey i want. I want this channel to be the elevator, because the elevator is on channel three, so we change this output source to the elevator and save now the motor has jumped over to this channel here and we still have to change our our steering. Currently, you can leave it as is, if you’re comfortable with it or, if you like it, but what i normally like to do is just change these around to my liking. So we know that the throttle the throttle is set on for our servo, but we want it on channel 4, which is rudder, so we will go here to the simple menu again and then go down here to output source and find our our rudder find. The rudder there we go and we can do save now. If we do left and right on the left, stick it shows, or you can hear the um servo moving and the cool thing about. It is a lot of the times for me, at least when i, when i do a right steer it actually stares left. So what that, what that means is um, i just have it backwards, so i could.
I could just flip the voltage here relatively easy. What you can do is you can go back to this a simple menu here and here you just hit the enter menu or the enter button, and if and it flips the polarity of it and now, if you go back, you have to save it and if You go back, you can steer it and it will go right when you steer right and when you go left it will stir left same goes for the motor for the motor. If you happen to uh push the stick up, and it goes reverse and that’s really confusing to you – you can go back into this menu here, go back to the source, the output source flip the uh voltage on it now go back to save. derpå. Once you go, you you press up on the stick, it goes up and go if you, if you push down on the stick, it goes down so it’s. Really that simple that’s all i do the transmitter is completely stock. I don’t i don’t, have any modifications to it. I just loaded the firmware and started using it. There’S, actually a lot more ways. You can program the receiver, but i don’t know how i’ll have to figure that out, but other than that that’s.