Ein must have rc-Tool!!

I want to do this product review um. I had this for a little while, probably about two or three weeks. Now i got these from rex welch this. These are his um engine tools. Um. This part right here is for, instead of having to use the tie wraps to put down in the engine to get your um sleeve out. You just insert this down in your um in your um inside of the sleeve right here, and it pulls your sleeve out and also this one right here, the long one. This one goes down inside the um carburetor, take the carburetor out and put it down and goes inside your crank for those when you putting on your um flywheel and your um crank just keep turning and not stopping. You can put this inside the crank window. This one right here put that one down inside the crank window and this will keep the crank from turning while you’re tightening up your flywheel so but yeah yeah. I just want to show you all this product review, but i teach how to ttr team tip tuesday and um i’m going to use it and demonstrate it and y’all just hold on right: Schnelle, Okay, i’m back y’all. So i got this tool inserted down inside this sleeve of the engine and i got it. Let me show y’all okay, so basically what you do is insert this lead insert the tool inside the engine like this, and then you push it back back towards the opening of the exhaust port, see that ledge is going to catch the bottom of your sleeve, but It’S going to go against the um, this is plastic, so it’s not going to scratch the engine up and it’s not going to break like a tie wrap.

So you insert the tool inside the sleeve like this, and you push it make sure your engine is at bottom dead center tripod make sure you enter that bottom dead center and you put just put a screw inside your crank. Genau so, like i got, use a 2.5 allen wrench to turn the screw down to bottom dead center once you get to get it down to bottom dead center. Like i got, my piston is right here, and this is the the worn out sleeve on my reds r5r team edition engine. Mittelmäßig, basically all you do is just put this little notch right here, push it down, put it down in the inside the sleeve. You want to push it towards the back of the engine and it’s going to catch the exhaust port, so you push put the tool in push it back until it catches the exhaust port like this, then once it catches it, you can also put some tension on I’M, trying to do this with one hand, because my tripod is not working actually it’s broke, so y’all bear with me. So i’ll put a little tension on it, wie ich sage, it’s catching the the rear exhaust port, so i’m gon na push it back a little more okay. Now you do it just once you catch the back. You just turn. You just turn your screwdriver turn. You turn your allen. Wrench turn your um you’re driving and the sleeve should pop right on up here.

We go should pop right on up. Maybe i got it in that too far, because you can’t put it and it might catch the block too. So put it just right, y’all better! Bitte schön, get it right position again. Here we go one two, so you got two sides, one side, a little bit more flanged out than the other one. That was a bad one i’m, trying to do with one hand. So y’all bear with me, but i got ta show my family what’s up, so y’all can holler at rick’s and he’ll hook. You up. He sent me these after. I did the interview with him so so see just like that. Just that easy i’ll push it back down. Tun Sie es noch einmal, so we can y’all can see how it go again, push it back down, so i just want just gon na put this. This flange edge right here back to the back of the exhaust port with the ink with the piston at bottom dead center. You just push the tool back, which that look that little flange edge at the bottom is going to go inside the port, the exhaust port and catch the sleeve, and once you turn turn your wrench. This leads your pop up just like that see just that easy. Y’All hell i holler rex welch, see you guys, look his little missions on there i’ll. Let him get you out some tools. Just that easy. You got ta worry about this.

The um you ain’t got ta worry about the tie, wraps popping and breaking on you, because this tool do all the work, so you ain’t got ta worry about breaking the top reps, get this tool it’s very handy. Just that easy y’all saw just that easy, like i said it took me a while, because i’m using one hand so um so yeah and, like i said the um, this other piece right here, this other piece right here like i said it goes down inside the Crank, this is just when you, when you can’t, tighten up your flywheel and it keeps spinning because of the crank, keep keep turning see. So you just put this to put this two two down inside down inside your crank, so ja, ich bin, sorry y’all but yeah. Just put the two put the two down inside the crank just like this put it in there like that and then got your flywheel on. You know i’m, just gon na simulate it put a flywheel on. So let me take this screw out. I’Ll show you! I need to put it on that type. Take this screw out right, quick yeah! I can see. I can see this tool keeping the flywheel from spinning just set it down inside the opening of the crank, like i said when you get ready for those engines that, when you put the flywheel on and it won’t tighten up and just put that tool put this Tool down the side inside the opening of the crank window, see to the crank close open it take the two, take the two put it down inside of there, just like that and it’s just a it’s, just like a piston stop tool, but instead of putting all That stress on your piston and your rod and your bearings and stuff this is much better because it just stops stops the crank stops the crank from turning over so and put the screw in there.

Y’All can see how it stops the crank so see see it stops the cranks from turning see. So if you want to tighten your flywheel down with the um nut, it’s going to top see it’s going to stop the crank from turning so yeah y’all highlight rex welch that’s, what i say man all these other modders. I don’t see them making tools like this. That help us nitro lovers, so i don’t y’all, i mean y’all use who you want to use, but you see rex welch work, not just y’all see his work. You know modern engines and and put engines up on video showing you the best engines to get. He also makes us tools to use rex. Welch rw mars makes us tools to use can’t beat it can’t beat it so hey y’all are free to use who you want to use, aber du kannst nicht, be the man they’re gon na put his work up on on video show. He show you his work. Show you what to do show up show us reviews of engines to get. He just did a review on the engine um that um crf the performer engine 3 port. He just did a review on that engine. das 209 dollar engine good budget engine to get three port pin of power and um look you can’t, beat it. Making those tools to use too hollet wrecks see how i was how easy it was to get that piston up out of there look it’s out just the worn out piston that i was running in his engine, so can’t beat that engine mod look 10r fuse! No rust look at this shiny.

Schau dir das an 10. Our fuels see that so yeah here’s the new, the new pistol then, like i said i’m out i’m, probably going to make send this old piston off. I mean it’s old sleeve off to get it pinched again. So i have still have two good um, two sleeves: send it to wrecks pinch, your stuff for 30 An 25 Stunden, get a fresh new engine pinch and he gon na look over your whole engine and bearings make sure they are good for 30 Dollar. So yeah y’all ekj 24 000 showing y’all the new, the piston, the um engine tools from wix rex welch at rw mods. This is full of, like i say this: go down in the car in a carburetor hole for your crank, opening, keep it from spinning on you when you’re trying to take your flywheel off this one is for you to x to extract your sleeve. Y’All saw how easy it was. I did it with fumbling because i’m, using just one hand and trying to video but yeah, ekj 24 000, bringing y’all the best products and giving y’all all the 911. and y’all know what’s up, but hey treat people the way you want to be treated. Let me haters be your motivators, Hallöchen, let them actions speak louder than words. Y’All know who it is. Ekj doing my thing: Hallöchen, family, love, y’all! Thank you for all the support and i just wan na you know tell everybody hey check out my videos check out my my interviews just trying to bring y’all some content.

You know we want big, happy happy family, rc family. Also, hey later, let me show y’all this awesome video check this out Music on the alley.