Today i want to talk about a common problem with rc cars, and that is the red blinking led of death. You may have an arma or some other vehicle low seat or something like that and uh. You may find that you’re getting this red blinking led of death, your car doesn’t move uh. It seems like you still have steering, but you can’t figure out what’s wrong. You call up horizon hobby. They actually give you the wrong information until your esc is toast, but is it really so? I just want to cover this as well as the solution, so we’ll kind of get into it. I’Ve got my armor granite. 4X4. 3S blx right here. I’Ve got my slt3 radio i’ve got the radio on on. Όπως μπορείτε να δείτε, my jen’s ace battery go ahead and turn on the car. Here my fans kind of dying and you get this red blinking led you pull the throttle, nothing seems to happen. Εντάξει, you got no power, turn the steering wheel, though hmm you got steering, so you obviously have signal to the esc. You obviously have signal to the steer but you’re able to turn the wheels, but the car does not move. So what is wrong? Call it horizon? They’Re, like oh, your esc, is bad uh. Wait two months we’ll, send you out a new one and you’re like uh, Εντάξει, that kind of sucks and horizon honestly probably gets about thousands of dollars of returned escs that are actually not bad, so i’m going to cover.
How do you fix this? What is actually going on so we’ll turn this thing off, and the thing i want to talk about is that when you turn on the car, obviously the car is going to get both throttle and steering sent to it by the radio and when it gets to Steering it’s going to turn the servo to where the steering is according to where you have the steering wheel turn the other thing it’s going to do is send power to the throttle, depending on what it thinks you’re doing with the trigger. Now there is this little tricky knob right here that says th right there in the middle it stands for throttle and you’re, probably wondering what is that knob? Καλά, it is the throttle trim and what that little knob does is send a signal to the car when your uh trigger is at neutral. So when you let go of the trigger, what signal is it going to send and if you also notice, there’s a little dot? So if you turn that wheel that little arrow up to the dot it’s going to send zero? So when you let the trigger at zero – and you uh turn on the car it’s going to send zero signal now on some cars like a nitro car, maybe zero isn’t, quite right, you want a little idle or something you might turn it up a little bit Or maybe it’s off a little bit, you want to turn it down, but really what you want is to always have that thing at that little dot.
That means zero. When you let go of the trigger it’s going to send zero to the car. Nwo, when you turn on the car, it expects zero for the throttle, and the reason for that is. It does not want to just launch this car straight into the wall. In case you actually have the trigger pulled. So normally, if you pull the trigger turn on the car, well it’s just going to launch the car straight into the wall. So it has basically kind of this protection that when you turn on the car it expects the throttle to be at zero or neutral. It does not want you to have the trigger pulled when you turn on the car. If you turn this little knob up a little bit or down a little bit, it thinks you’re trying to send it either a little positive throttle or a little negative. You know like reverse and it won’t. Let you turn on the car so watch. We set that little arrow up to um the middle right. There neutral turn on the car. You don’t have that little blinking red led of death. We got throttle, we got reverse we got steering car is good to go it’s fixed voila, so that is what’s going on when you get that red blinking led of death check this out, make sure your throttle is at neutral and then see if it actually runs. You obviously have to turn off the car turn it back on.
If that does not work. The other thing you can do is calibrate your esc, so i do have a whole video on how to calibrate the ec and what that actually does is you’re programming, the esc, with where that neutral position is where the full throttle is where the reverse is, and I do tell you in that video that when you calibrate the esc always make sure this knob is at zero at the middle and never ever ever change it again, because once you change it turn on the car. Καλά, you get that red blinking led of death.