Ahora, whilst the Ronin s app does have an onscreen, joystick and you’re able to use it to control the gimbal itself, it only works up to 10 O 15 meters because it is bluetooth and once you get beyond that range, the signal drops and you lose control. If you did want the ability to control it on a further distance, the way to do it is using a standard, RC receiver and a remote controller, because DJI have built in this functionality, as well as the ability to use the external remote controller that they’ll have Available coming soon now, you may or may not have noticed that on one side of the focus wheel, there is an esper stroke and the switch. así que, to use this, you will need to place it into the S bus setting and then on the other side of the focus wheel and for me that’s on the bottom, because I’m left handed and I’ve got it on the left right hand, side. You then have a little plug and that plug is for pins. You will only need to use three of them, connect it to your s, bus receiver and then use it on your remote controller to control the gimbal. Now the wiring, for this is not the same as a standard RC connector. Normally you have ground five volt in the middle and then signal for your S, bus on a normal receiver wiring, Sin embargo, because this is DJI scam, bus connector, it is slightly different.
Pin 1 Es 5 volt pin 2 is ground and pin 3 is still signal and I’m going to stop right there, because I’ve said something wrong: it is actually pin 4. That is signal. So number 1 is voltage. Plus number 2 is ground and pin 4 is signal when I record that there somehow I managed to change it between getting from my workshop back to the computer. Please note, if you hear me say: pin 3, I actually mean pin fall to do this. Looking at the front of the focus wheel, pin 1 is the closest pin to the front, which is the 5 volt connector the next one back is then ground and then the third one is the signal wire now for purposes of this I’ve simply used a temporary Cable that allows me to demonstrate it for you guys now it uses channels one to fall on your radio and you will need to set them, as you would normally set it on any standard setup, and once you’ve done it, you then have control over the pan Motor you have control over the pitch up and down, as well as the roll motor on the back and what it means is over great distances. You will be able to control your gimbal and do some actually quite interesting moves if you didn’t want to use the onboard features with the DJI Ronin app. Now there is one or two little downsides to this, and the first is: you cannot control the camera itself and what I’m about to say is specific to F R sky, because it does work with Futaba radios.
Please check out my other video, which I’m going to release, which will talk about this specifically. But the information I’m saying here is correct at the time of posting for F R sky radios I’m, using this with the gh 5, which does have focus and startstop control over the onboard functions with the Ronin S. Sin embargo, they haven’t appeared to have programmed a channel that allows you to trigger that I’ve tested it on all of the aspects, channels that I have available and none of them trigger the focus or the startstop record, or the all the shutter on the camera itself. Desafortunadamente, so if you were doing this manual, camera control would have to be done next to the unit where you’d have to set it and then move a distance. Now what it does mean by doing this is you can use it up to any range? You really want to on the capability of your receiver. Through the to this. I have actually seen someone post a video of them using it with DJI Lightbridge to and what they then done is plug the HDMI port into the side of the camera, the d bus s, bus into the bottom of the roll in s and that’s. Given them wireless control and video over a much greater range, so it is something else you could do if you were looking for that remote control. So if you’ve mounted the Ronin S on an on it of a vehicle or something like that and you didn’t want to use the Bluetooth, then this gives you another option that is it for this video.
I hope the information has been useful. Please do subscribe to the channel if you’d like to support the channel. There are some links in the description please to use them.