Neumáticos Ryft Vitavon trans y Mamba

I got vidavon front axle, lid of on arms, vidivon, rear axle and now vidivon transmission case. This is going. This thing is like a nat. It just kind of shows up at different places anyway. This is going into the rift. Take a look so here we are let’s. Take a good look at this beautiful work now. Is it heavier than the stock transmission? Por supuesto que es, but you know it’s not that bad, not heavy at all. Really now one thing about the aluminum is all of this right here can kind of become a heat sink. así que, if you’re having motor temperature issues, this right here can actually get some of the heat out of your motor. So and this thing is not going to flex at all, so it’s phenomenal got a nice little cap right there for the two speed. Whenever that’s available. This thing is nice, guys now, while i’m in here doing this i’m, also going to finally change out that esc got a new mamba x, because i need that monster x, someplace else now, as far as getting into this it’s, actually pretty simple i’m, just simply going To take the shocks loose up at the top since it’s right, there take the sway bar loose four bolts on this side, four bolts on the other side and the two bolts right there, along with that zip tie and the entire drive line, will drop right down When you have all that out, this is what you have right here.

You can see all the sand from the last run got to do some cleanup on that, but i get all this out. The esc actually knocked loose so yeah interesting there you got ta pull the receiver cap off the whole transmission. Everything will be out on the table here in just a few seconds: son, both out now it’s time to take them apart, Music and there you have the whole case and it is set up and pretty darn nice. I got ta say all right, Muy bien. Muy bien, it appears these two arms right here actually bolted in place, all right beautiful in there look at that. Espero, you guys can see all that very nice a little dirty in there isn’t it wow that motor right there is awesome, even though holmes recommends the uh polar pro like 2700, the crawler but uh. This motor right here does awesome Music lots of beef in there guys lots of beef. Ahora, as we pulled all this stuff out, got to realize the way this is set up, you’re going to be using some of these stock bearings. En realidad, most all of them got that bearing right there to get out, probably just going to go ahead and swap that out. Since that looks like a normal sized bearing so no need to do too much with it. Bien, De todos modos, clean up a few things, and then everything will then go back into here. Bien, we’re gon na get this started now these right here they just simply push right in and yeah outside, bearing is a rubber sealed, and then you put that bearing right into place there so there we are with that.

This right here goes into here. You got a good little turn, so the flats line up, but there you are with that now we have this guy right here. Bien, not that guy right there sort of that guy right there, así como así. Ahora, when i took it off, i actually pulled this off and you guys could see everything sticking out of it, so i’m kind of putting it back together a little bit differently, but overall it’s the same thing. I want you guys to see. I did in fact remember to grease it now, maybe quite a bit of grease here, but most of this grease is just simply going to sling off the gears at the first time. I rev it and it’ll be stuck to the outside case, so might as well have a little bit in there right. If you do like your orange cover or your black cover, it will go on so, as for me, i’m covering it with that right there. This thing is starting to remind me of the udr i’ve got everything in there now. The mamba xcsc is quite a bit smaller and i do recall hearing the fan come on with the monster x, so we’ll just have to see how that works out. Wow now it’s time to get this back into the chassis. Hopefully i don’t have an issue with this guys, it’s all in and ready to go we’re going to power this thing up with a 4s and take it out and rip some sand.

Well guys, this time we’re running out of the hill, this is the softest sand. I can find out there at the uh sand lot, es, not so soft. There we go oh yeah, and this is what i want to get since we have zero mud right now. These things are working like paddles that’s, exactly what i wanted to see come on baby bog down bog down there, we Music go Music and of course, you guys know. I want to try to do my burnout right, Wow, música hermosa. Aquí vamos. That is awesome and we have this obviously we’re not going up it, but we can try to backflip it right. I think i missed that. Así es. I didn’t go up high enough Music, what a hit and that’s enough of those, my god ow. That was a hard hit right on a wheel, looks like it survived it. That was also a hard hit: Music uh, ah uh Music. I can do better than that. Música. Keep all the weeds out of my bearings. Get this just right here there we go kind of wonder if i could backflip that. así que, if i wonder it, i think i’m gon na have to try it in position. Another side hit these wheels are going to hate me. Oh, espera un minuto! Something else hates me too, oh looks like our run is over and you’re about to see why Applause get me out of the shadow.

I finally broke a lincoln yeah. Those side hits they are hard. Hard hits well. I’M gon na steal a throttle at one time. Just to see what happens here, this is a bad position to be in oh see that back axle move well there you go guys good run, though so i’m out there doing a transmission video right, and it turns pretty much into another tire test. Just because these things are awesome, uh transmission, hermoso, no issues at all. I did try a 13 tooth pinion from techno, and i had the same noise. I had from the 14 tooth that i had on it previously i’m, not sure if axial change the tooth profile or something, but the 17 had to go back in. I wanted to try to crawl it. You know drop it down a little bit, but just didn’t seem to work out very well, but regardless of all that uh they weren’t good. I did break the rear link, but those side hits they were rough. What i did like when you sink this thing down to the axle you just throttle it up, it still took off and made the climbs. These things are almost like paddles in that sand, which means they’ll be just like paddles in the mud, so they should stay on top if you got enough power yeah, but anyway guys. Hopefully you like that video in that description, i’m gon na put a link to everything i can find on here.

The axles the housings are hard to get when they pop up they’re gone they’re just gone as fast as they pop up. You know so, but i know i can find i believe i can find the links in the transmission case find those for you, but anyway guys uh check that description. They are affiliate links, ebay, Amazon, amain and horizon use those links to help out the channel. It means a lot to me so guys hey! Thank you all for watching guys if you like what you see hit that like button hit, that subscribe button and ring that bell so in the description, there’s a link to become a channel. Remember if you want to become a channel member it’s, a very simple two dollars: five dollars, ten dollars or if you really got some money 25 a month, it’s a simple way to support the channel so get that and i am doing monthly giveaways for members. Only so you might want to consider it so guys here’s, those links make sure you’re subscribed.