Maar goed., let me get the camera down and show you what’s in this box, because there are so many good goodies in here. It’S untrue. But if you like, what you see in this box, i’ll put a link to them below the video, because jacob is now selling these on jacob has sent me all of these awesome 3d printed goodies to fit to the max. So what do we got in the box? Goed, we’ve got a whole load of 3d printed parts, everything from front bumpers, to rear bumpers, to roof protectors in a little funky, biohazard ones like this in red and black little very funky little spider logo on there. Toch. Let me get everything out on the side and then let’s fit them to the max and see what they look like with the light bar well. This is one of the best care packages i’ve received in absolutely ages. We’Ve got the back bumper with back off button. Both available in a grey and a black and my rear light bar will shine through from those, although they do come with the inserts fitted. If you’ve not got light bar fitted, you can still fit them to the car. We’Ve also got these custom front bumpers in grey and black with a little alien header. These top protectors are available in two different styles in grey red and black in the spider and the biohazard design on those fit under the side rails.
Here so the spider’s head or the buyer has a symbol will appear on here, so we’ll fit those to the car in just a second i’ve got the light bar fitted to this car, zowel voor- als achterzijde, so that is going to poke through on there. Removing the existing bumper and fitting this one over the top of the light bar and exactly the same at the front, so let’s get to work with two little inserts 4×4 logo on them as well, complete with all the fixings on there and the new front. Bumper entirely replaces the existing front, bumper all you’re, going to need to do if you’ve got. The light bar fitted is to undo the two screws from behind it, enabling you to slide the light bar out how easy these are to fit. You’Ve only got to remove four screws at the front two either side of the bumper to release the bumper and then two to release the light bar itself. You’Ve then got to release the wire from the inside and the same on the back release the wire there and another four screws on the back. So it should be fairly easy to get done if you fitness to a car without a light bulb, it actually comes with a fixing that holds this little piece of white plastic in the back there. But if you fit into the one, with the light bar just undo, two screws push that back and the light bar’s gon na slide in there light bar simply slides back in from behind using two screws that come with fasten that on two in the bumper and We’Re back on i’ve got the front bumper on.
If i fill in these and a little wicked front and rear when they’re loaded i’ve got the back off bumper fitted to the rear light bar now time to put my red blower hazard logo to the top here. In order to do that, just to remove those four screws from the inside now i was wondering what the ridges cut out in the side of all of these are, but they are to locate on the top ridges of the uh max there, the rubbing strip rails From you, flip upside down or slide upside down simply clip over the top there, keeping this nice and securely on the car. As i say they come in several different designs. Eigenlijk, let me know in the comments section: what do you prefer? Do you prefer the biohazard one? Do you prefer silver? Do you prefer black because i’m sure jacob would like the feedback from people when deciding what colors or what about a green one for the biohazard would be done in green, and these are made of a carbon composite as well, so they should prove quite tough. I might take them with a black spider actually, but i think we’ll stick with my original choice of the red biohazard, so with everything fitted to the car just check out that front light bar and the rear one with that awesome back off logo. Eigenlijk, let’s see what they look like in the dark: oh and they are even better in the dark, just check that out at the back, nothing looks plain evil on there and at the front, the alien eyes.
Kijken, absolutely awesome. I’Ll just move up here see if i can get a better angle on them, as their thing is thumping out light and moving on forwards from the rear light bar that’s. My biohazard logo installed on the top of the truck well, i have to say i’m very pleased with the look and the feel of these 3d parts from rc 3d loving. The look of my little alien head and the back off bumper is just absolutely awesome, and i mentioned the look and feel of them. They certainly feel very tough. Indeed, they do have carbon in them, so they should be nice and durable anyway. Many thanks to jacob for sending me all these rc 3d parts very, very impressed indeed with the quality of them link to all the rc 3d stuff, including the front and the rear bumpers below the video thanks for watching well thumbs up.