Okk. Więc to, co masz przed tutaj to scx 10. Teraz jest to oryginalna wersja scx10, nie dwa, a nie trzy. This is the number one. Okk, now the scx10s come with a pretty large transmission and motor mounts in the middle okay of the chassis that’s. The traditional uh scx 10, sometimes they’re a little bigger little smaller transmissions, but pretty much they’re all pretty standard right. Więc umm. I bought a jeep body. Wrangler body for it this one right here and you guys saw a picture of it. Um in the intro okay, this body, according to endora, store and amazon, is supposed to fit this chassis it’s made for the scx10. It doesn’t have any other numbers on there. It doesn’t say that it fits a gen, trx4 or a redcat 7. It says it fits the sex 10.. Dobrze, as you could see, it does not fit an scx 10. Teraz um, i typically won’t say anything. I i rarely do a negative review uh, but anjora needs to stop doing this um it’s. Zasadzie, a big lie as far as i’m concerned, Ponieważ, if, if if they said this body fits an scx10 and i went and put it on a trx4 and had to modify it, i would understand that or if i went and put it on a gen 8 And i had to modify it. I would understand that, because i’m putting it on something that they don’t they don’t recommend.
They recommend that it goes on an scx10, every video that i’ve seen out there. If you want to put this body on an scx10 you’re going to do two things you’re either going to, let me put it on pause for one so on every video i’ve seen um. If you want to get this body on an scx10 you’re going to have to cut out the bottom here, so that the transmission will fit in there, Okk, so you’re going to ruin basically you’re going to ruin a very nice body – Okk, very highly detailed. So i do like the endura bodies, i just don’t, like their engineering and, like i said i normally don’t, say anything uh i just suck it up and and do the modifications. The other way is it’s gon na sit really high, okay kind of gives it a monster truck. Wyglądać, you know what i mean it’s up about three four five inches up off the chassis. The whole bottom of the chassis is exposed. Więc, in order not to do that, you’re gon na have to cut up that body and get the transmission and it’s going to go through the body. On a on on a lexan body, i don’t mind, but on a nice body like this, i i don’t believe that if, if a manufacturer says it’s for a specific chassis, then it should fit almost like a glove. I realize sometimes you might have to do a little bit of tweaking, but you shouldn’t have to do major modifications, okay and that’s, just my personal feeling on it so um.
I wanted to share it because i do like the body i do like the detail, but i don’t like the fact that many these manufacturers out there are selling rc bodies that don’t fit the trucks that they’re supposed to fit. Okay as far as i’m concerned. If you tell me it’s for an scx 10, it should fit an xcx 10, almost like a glove. You know maybe a couple a little tweaking here and there, but you shouldn’t have to cut up your body so that’s my complaint with it. So um i’m. Almost five minutes into this video – and i did not want to do that, but i did want to show you what the issue is with endura bodies – and this is, Tak myślę, enjoy – is going to go bye, bye on their bodies someday soon, because unless they start Making 3d printed bodies, which i really am liking, the 3d printed bodies better um, and then i can do my own interior, but i i hate to have a beautiful interior and truck like this and then have to chop it up to make it fit so that’s. My complaint, so this is part one and then on part, two i’m going to show you how to mount it on a gen 8 because it will fit on a gen 8 without you having to chop up the body okay. So this is xd40 luau.