
Bulldog Remote Transmitter Programming
The first section being as if you had no remote lost your remote and your starting from scratch. So that, É claro, is the worst case scenario. Now I have the main module this one here, in my hand, is a model rs80 to be okay. It doesn’t matter. If this is your exact one, but close enough I’m sure Bulldog is pretty, you know straightforward across their lines, most of their systems look very much the same. Olhe para isso.. They actually give you an 800 number to call which is hard to read I’m showing that camera, but if you need it anyway, what the heck eight hundred eight seven, eight eight thousand seven. But what do you need them for you got me so I’m sure you got your remotes there and you bought them from me because I got the best deals on them now. Let’S just get back to it. Nwo, if you have no remotes, all gone, no remotes, so what you need to do is you need to do. What’S called a master reset on your system and how you do this? Is you get in your vehicle? Sit down your seat. Take your brake hold it down and don’t. Let go keep holding it. Then you have to take your key cycle. It like this on off on off on off on off on off, so you got five times, you’re, turning it on and off five times. At that point, release the brake take the key out of the ignition get underneath your dash.
You should already have this, this main brain module – handy unplug, all your harnesses from here, so you got this secondary harness this plug over here. All your powers disconnect all that stuff leave it alone for about a half a minute or a minute, or so what this is going to do is going to tell the brain once you plug it back in it’s, going to start looking for a new RF code, Automatically so once you plug all the stuff back into the brain, the units going to click three times and the lights will blink most likely on depending on the model. OKEY, once that happens, you’re going to get in there say if you only have one remote just hit any button on that transmitter hold it until it confirms by clicking back at you now, you’ve learned over most successfully okay, but in this case we’re going to use Two to make it a little bit more difficult for me and more helpful for you, because you may have two three or even four remotes for your system, so I want to do a thorough job and cover all this stuff. So we already know that we programmed this one here successfully now let’s move on to adding a transmitter. OKEY. So what you’re going to do? There is you’re going to press and hold the break and hold down button, one on the working remote for approximately five seconds or until the parking lights.
Flash one time release button. One on this remote and press any button on the new remote. The parking lights will flash three times and the new secondary remote will be learned, and you would repeat that if you had a third or a fourth transmitter that’s all there is to it it’s, not a very complicated thing, at least when you have the information available To you it’s much more helpful and thankfully I’m sure people are going to be thankful, because this company got bought out by the worst company there is, which is Viper, and God knows their tech support is non existent. Então, thank God that people like me share this information, Porque, when bulldog sold to them, the whole thing went downhill, é, not the same, and just another note on the remotes that I’m, using just for your own reference this one here. The two button is a TX 2 BD. Tx is 4 Transmissor. 2 is for the amount of buttons BDS 4 Bulldog. This four button that I’m utilizing here is on the bottom. It says C 705 and above it it has a really long numbers J 3. The hell is that say: I can’t see it J 3 s: 0. 0. 4 s CH oo.
[compare_prices_deals]
Fonte
Have you had any customers install the Bulldog on a Polaris Ranger ?
Your hand is twitching outn
I have an m200 bulldog brain with no fob. how can I get one??
ok have a bulldog rs1100. initially installed with pk05 bypass module alternator shot craps and blew module i believe tried toreload flash with xkloader to noo avail. rs1100 works if key is in or close. ordered pkall spent two days figuring out instructions does not work. I think instructions are way to vague for diy'er.
after module died attempted to remove chip from spare key and shorted it out. Any advise here will be greatly appreciated, Obrigado.
Could this system cause a missfire if not installed correctly?
i tried to add a remote and it will not do it. same remote as the one i had
Oi, i have the same model with built in by pass and the parking lights dont come on and fails to start completely due to the passlock 2 on my 04 cavalier. can you help me out? i called the hotline for BD but the one man operation is useless and doesnt seem to know anything about this model. Hopefully you can help me asap its getting cold out now. Obrigado!
added my new remote in a matter of seconds. very simple, Obrigado.
Does it work with any model?
Eu tenho um 1995 Infiniti J30
Tried doing what u said soon as I plugged everything back in the unit just non stop clicking and truck interior dings non stop and dash cluster lights glitchy, I'm lost, unhooked the unit , any help would be appreciated Tia
How do you reprogram it for keys with transponders? I just had a key made for my new (Usado) truck with this installed. The remote start worked before and now the locksmith refuses to help. There must be a bypass of some kind that is still programmed for the old transponder key. How can I make it bypass for the new keys?
Thank you for posting this !! I was able to do it myself
I have an older one. it only runs for 2 min. just bought the truck?
Ei, I've done what my instructions said and what you've said and nothing happens. but when I click a button on my four button remote I do here a click from a relay connected to it. I had no remotes to begin with.
well I tried what you said in this video and now all it does is making the 4 ways flash and the remote with knew battery is still not working I had to unplugged the whole thing so the lights will stop flashing .
Hi got a question for ya, I just changed the battery in my remote (TX2BD) and the thing doesn't work anymore I don't have 2 remotes just this one. Do you need to reprogram the remote each time you change the battery ? and how can I reprogram this one only ? do I need to do the 5 times shut off with brakes on like you said and unplug all the wiring ? just to change a battery in the remote ? Obrigado
hey bud, i need a new remote, its a two button, the tech support said i need a TX2BL, i still have the old one,just doesnt work, if thats the one i need ,how much to ship me one?
This fixed my F-350 diesel, the Bulldog remote start system did not work when I bought the truck 6 mos ago. I unplugged it and cycled it as per your instructions from start to finish. This fixed it.
Thanks from north of the 49th!!
Hi i have a bulldog 500 install in my truck, but after a year it dos not work any more, when i try to star the truck its sound like it will but in the next 30 seconds the engine will die. Does anybody know how to fix this issue?
Hi all,i have a problem with my EZ-75 remote start system.The 2 way remote its not working, how can i reprogram it ? Obrigado
So I am not seeing the list of which cars this unit works on. I went to the bulldog website, nothing. So I have a Buick 07 LaCrosse, I would really like to not have to go pay $100 to replace a remote!
Is there eny way I can get a chevy key fob and mod it or somthing so I can use a chevy key fob on my bull dog system
My bull dog remote has always worked good, weather got colder and I found out it no longer works. I tried what you showed in video but I get nothing, checked power to unit, checked switch under hood, even check all fuses and also put in new battery in transmitter. When I tried to reset unit I got nothing, no sound or flashing light. Tried resetting transmitter and also nothing, what do u think is wrong? Do I maybe need a new transmitter, how do I find out if mine is bad?
What if I want to install the receiver for the first time?