The pilot of that inverted hovering helicopter. My radio is right here, assalamu, alaikum and greetings only sharma here and welcome to my little main cave and more yes, helicopter videos, rc helicopter videos. Сегодня, in this video, the long awaited h1 gps helicopter that is flying fw, 450 v2 it’s right there. It is right here it has got: omni gps, 3d fly, auto inversion and all those features that i have shown you before in fw 450 videos plus more and new upgrades that make your life even easier. So let’s open the box let’s see how it comes inside. The box, i will assemble it then we’ll, take a closer look at all the components and talk about what’s new in this helicopter and after that. Да, this is another bonus content coming your way in my videos, and that is, people were asking a whole lot before when the fw 450 was released, that hey, how do you set up a pnp version with radiomaster tx16s or any other radio control? Сооо, Да, i listen to you people. Thank you very much for your feedback. I have got the v2 fw 450 pmp version without any radio control and lucky me, i have my radio master tx16s max edition just arrived. You must have watched the video review of that. So i’m gon na set the fw 450 v2 pnp version with my radio master, tx16s and i’ll post a complete video tutorial how to set up radiomaster tx16s with your pnp version of fw, 450 v2 helicopter fly it and enjoy so that will come in later videos For this video let’s get to work, all right here is the fly wing, fw 450 давайте.
Take it outside the box and see what’s inside the box. Честно, i haven’t opened the box since it arrived. I was waiting for my radio master tx16s max edition now before we open the box once again, omni gps 3d fly auto inversion. It has the gps features. Также, look at this omnidirectional gps based localization technology, full range of position, rescue automatic inversion, one key or low power return to home and lan intelligent recognition, 3s or 4s lipo battery nice. There are some upgrades. This means check this out. This is how it comes packed in the box. This is the pnp version that i have received is a user manual fw 450l helicopter, smart, heli, okay and yeah hold on. Let me just leave it, so i can use both of my hands. О, посмотрите на это. Это 4450 milliamp 4s battery, so this is a high voltage, 4s 4450mah battery that came with the with the helicopter, normally i’m, Не уверен. If it will come with yours or not, but mine came with it because i requested for a battery, then we have 3d blades and the tail motor with two blade propeller. This time before i had a three blade propeller now i have only two blade: propeller and an mrr 30 m uh connector installed right here. That is a three pin connector. Then we have this tail, which is very interesting, because this is an upgraded feature. Focus on this one, i will demonstrate very very soon.
Gps looks different on this tail and here’s an up close view of the tail before in the older version. You had to insert this long cable and take it all the way through the boom. That was kind of headache, but now here it is already out very easy to install the motor and this side look at that. The connectors are already installed why you know why? Because now this is removable tail. So once your motor is installed, all you need to do is you know, fix it on the main fuselage easily. Хорошо, so here comes the main fuselage. Let me see anything else, nothing else inside. So this is the main fuselage right here. Хорошо, let me just take this off the canopy and remove this thing. Хорошо, Ой. Посмотрите на это. I simply love the white color. It will be very difficult to see in the skies foggy cloudy skies, but having to have a white canopy. You have freedom to paint. It the way you want right, so you can put the stickers on it. You can paint it spray paint it. And yes, if you have access to a spray paint artist or your spray paint artist, all by yourself, you can spray paint this canopy. The way you want the color of your own choice and make it look amazing now this is your main rotor head – looks improved, cnc components to me compared to previous one. The design of these components is different as well.
Хорошо, then you have your h1 autopilot h1 lite autopilot installed right on the back side, just like before, and normally it’s configured for the rtf, but for pnp not so i will have to configure it and you can watch it completely down here. I see the metal main gear as well, and the belt is kind of slightly loose on it, which of course i can adjust it later before the flight on front. You will see a big improvement right here check this out. We have a 60 amp esc in a complete metal, cnc metal enclosure regarding the motor. I do not know if they have upgraded the motor or not. I still have to get the information previously. My only issue after a couple of flights was the motor started. Getting heated heating up when i used it with a 4s battery but wasn’t the case with 3s battery, so this one we’ll see because it came with the 4s battery will find out very very soon. If things are heating up or not now connecting your receiver to autopilot is easy. One cable s, bus connection and the gps connects right here and usbc, which you can use to connect it to your computer, the h1 lite autopilot and configure all the parameters now let’s check out the new feature, which is how to how easy it is to add The tail in there, if you can see there’s another three uh, connect three pin connector, which should get seated easily with this one.
Now you can see here there’s a handle which can loosen and tighten the screw to open this component here, where the tail will go in so let’s see how easy it is to put it in and out one moment just like this. Okay and i just need to seat those three connectors that’s, it it’s done and now that’s all i can tighten it. It is not gon na come out, it’s really difficult to pull, and now you can connect your gps right here very easy, and when you want to transport your helicopter – and you really do not have this much space well, you can always toss it in the back Seat of your car, but imagine if you’re on a motorcycle, you know and your saddle bags don’t have or backpack don’t have this space. It is absolutely simple: now just loosen this one make sure to pull the gps cable out with lock on it, there’s a lock on it. If you just pull the tail, you will break the cable so make sure first disconnect the gps, cable and, after that it’s just that easy to remove the tail. How cool is it? How easy the life is now make sure the connector on the tail goes in right and you don’t have to worry about it, because this connector will fit only one way, Хорошо, here’s my tool. I have to open this one. It was very tight kind of like lock tight on this man, okay and the second one.
I believe these are the only two components that comes with it, and all you need to do is push everything in with the motor here. Align these things just push everything in right here and put the screws in and make sure it is pointing downward, while the gps is to the top okay, so one do not tighten it and two and now you can tighten them very easily because you have done It right that’s it your tail is ready with the tail motor on it, and now all you need to do is insert it in seat those connectors properly and tighten. This now do not over tighten it. Конечно, enough. A little bit is enough and that’s it, and after that, your gps goes right. Там, there you go one click and gps is connected. I just need to add my you know: an sfhss bus receiver or a free sky receiver s, bus receiver. I have plenty of choices i believe now. I have got three of the radio master d16 pwms bus choices right here i have r86c kind of big nah. I will not go r168 also says eight channel pwm and s bus kind of big i’ll not go with it yeah. This one check this out baby r, one r161d16s bus receiver, because i just need one cable uh to plug in the h1 lite gps, autopilot that’s. That there you go, i mean look at this beauty mashallah. This is very, very beautiful, looking and i simply love the way they have improved the tail installation easily removable installing the motor on the tail was very, very simple and easy, and now having to have this pnp version, i can set it up with my radiomaster tx16s Max edition and show you a complete tutorial, some complete setup, video on my radio programming.
This is open. Tx multi protocol radio i’ll show you my complete radio programming and my programming on h1 gps, s1 lite gps autopilot, and after that i just can’t, wait to bring this baby out and test it and fly it and this time i really really want to test this. One in complete 3d mode, so stay tuned for next video. That is a video tutorial on how to set up fw 450 with radio master, tx16s, open, tx, radio control and flight videos. Thank you very much for watching this video don’t forget to subscribe and hit that little ding ding ding, bell icon, so you’ll stay updated for all the upcoming uploads. I am the pilot i’m. The pilot of that inverted hovering helicopter. My radio is right: Музыка, here, Музыка, Музыка, so Music, huh radio is down here. Helicopter is flying all by itself. Музыка, Music come on. You know what to do hit that like button it’s right there, i know you can do it. О, while you’re at it also hit the subscribe button right there come on don’t, be shy just hit it. Thank you very much for all your support towards my work that i post regular and fresh content on my channel.