In that previous video. I got the car up and running and working great. So now i can just focus on making the car look cool with some paint custom wheels and a few other mods. If you missed the previous video and want to catch up i’ll, be sure to post the link to that below. В описании, the car is looking pretty cool, as is, but i wanted to take it to the next level. So i started by modifying the body mount. I did the work off camera, but basically i just made it so that the body will sit more level as the front was a little high up before and i dropped the body down some to give the car a lower stance, which already makes it look cooler In my opinion, there were a few other changes i wanted to make first being switching to using a smaller battery, as well as i needed to modify the interior around the gears, as it’s now too low to clear them. Both of these modifications were pretty easy, starting with the battery, i made some more room in the rear of the body for it to fit. Однако, as you’ll soon see, i decided i’ll be mounting the battery to the chassis instead of the body, for the sake of simplicity, Музыка, to have enough room for the gears. I grinded down this section on the bottom of the interior. Как вы можете видеть, i went a little too far and broke through in a few spots.
I’Ll be fixing this later, but for now at least the gears have enough room. I needed to swap the battery connector on the esc, so it will be compatible with a smaller battery and yes, in this case, i needed to solder the black to red and red to black, to have the correct polarity with this new connector Music. I did a quick test after soldering to make sure everything is still functional Music. It was at this point that i decided it would be easier to secure the battery directly to the chassis rather than the body to do this, though i needed to remove most of the rear, undercarriage piece Music. I tried to save the tailpipes, but there just wasn’t enough material. I can now easily mount the battery to the back of the chassis. На данный момент, i wanted to do a quick test drive to make sure the body wouldn’t move around. So much as i mentioned in the previous video, the body moved around quite a bit when going over bumps and sharp turns. But after modifying the body mounts, the body seems to be staying pretty solid, despite not adding any additional magnets. I may still add some at some point in the future, but at this point the car is looking and driving well and i’m, ready to start modifying the appearance of the car. The first thing i wanted to do was swap the wheels, although i do kind of like the look of these rally wheels, i want to swap them out with something else just like in the previous video, where i designed some custom wheels for my 2010 shelby gt500.
I once again went over to carid.com and used their visualizer to look at a bunch of different wheels, just like with the gt500. Some wheels, certainly look better than others, but it’s a lot of fun to see all of the different options rather than designing something new. I decided to go with this set of wheels that i previously had on the 85 mustang svo. The stl files for these wheels can be found on patreon, using the link below in the description Music. I swapped out the rear wheels. Как вы можете видеть, i needed to remove the spacers that i had in the front, but after that i swapped out the front wheels as well. Музыка. The black doesn’t show up the best on camera, but i think they look great on this car. I removed the interior and glass, so i could start doing a little bodywork. I started by sanding away any imperfections. The best i could. The body does have some cracks and damage in a few spots, but i still wanted to spend a little time. Sanding, the body and removing some of these imperfections and preparing it for primer Music. Before applying the primer, i removed the chrome from the emblems with some alcohol and then thoroughly wash the body i applied some standard, gray, Автомобильной, primer, Музыка. I then sanded the entire body using 600 grit sandpaper Music. After another wash, i applied some silver duplicolor paint, followed by the gloss clear coat after only two light coats.
I unfortunately ran out of the silver paint, and i did all of this paint work in one evening, so the result wasn’t amazing, but good enough for a driver. This was just something i wanted to slap together right before uste and i’m, not overly concerned about the appearance i did try to polish it, but it’s still pretty rough after another thorough wash. I masked off this center trim and used an airbrush to paint it black. The trim turned out looking nice, but unfortunately, once again as a result of the rushed paint job, the masking tape took off some of the paint normally i’d repaint the car, but again with this being a driver i’m trying to put together quickly i’m just going to Leave it, as is, i will be painting the rest of the details by hand to avoid this happening again. I guess we’ll just call this car the craigslist special corvette. I do want to change gears here, real, quick and focus once again on the interior to cover the holes in the rear. I measured and then cut a piece of styrene to glue over top and then glued that into place Music. После этого, i applied some red paint while giving that some time to dry, i switched back to the body and began painting a bunch of details from the door handles to the taillights, although masking and using an airbrush would have given the best result. For most of these sections to save time and to prevent any more paint from peeling off, i just hand painted each of these details.
The body looks pretty cool. Once these details have been added, i cleaned up the glass with some polish and painted a few sections. Black i got ta say i really like the look of the tint that’s already on the glass Music. Although i didn’t fully detail the interior, i did paint the dash and steering wheel black just like it would be on the real car with all that painting complete. I secure the interior to the body Music, just one last thing to do and that’s to add the tailpipes. Since i had to cut the factory tailpipes off, i designed a very simple tailpipe piece that i could glue to the body using fusion 360.. Снова, this design can be found on patreon. I printed the parts made sure they fit and then painted them before gluing to the body Music, Музыка. The tailpipes really came out looking nice, even though i couldn’t make them too deep because of the battery Music. На данный момент, the car is complete, despite the paint job replicating a craigslist special overall. I really like how the car looks. I think the silver with the black wheels and red interior really works well on this car. I also really like the styling of the c4 corvette, so this is an overall really cool little car. I look forward to doing some driving, especially since i don’t have to worry about inflicting the first scratch or paint chip. If the body was in a little better shape, i might consider stripping the paint and starting over but i’m fine with it, as is, and would rather start over with a new undamaged body than spend more time on this car i’ll probably be putting this car up.
For sale after uste in case anyone’s interested otherwise it’s a fun car to cruise around the track, with speaking of crews around the track, although i’ve driven the car multiple times already, i figured i’d take it for another spin, with the car completed as i’ve said, it’s A lot of fun to drive Music and that’s going to wrap up this video. Thank you all very much for watching and don’t forget we’re. Just a couple weeks away from the ultimate skill trek expo down in williston florida you’ll find more info in the link below. In the description it’s a great time – and i hope to see a lot of you – there that’s all for this video.