When you um, do a speed run front splitter on this put some lights on it and uh reinforced the rear wing with some carbon fiber tape, as you can see, put the front uh front wrist side skirts on there and i’ll run that with you run through That front splitter so, like i said, um a lot of people going with the pet uh body shells on this, but what i thought i’d do: i’d. Um stick to the original shell. I had a lot of problem with the uh fitting the electronics in brushless, motor or whatnot, so just got a rear, pin, um rear, pin body pin and raised the rear up left the front stock. So the front height pin, is stock height, uh, raise the rear, pin up and then put these slide skirts, which i actually attached to the actual chassis, where you got the um, the plastic uh side running um let’s just attach these bits on uh reinforce the shell. A little bit put front lights on there, um and i’ve upgraded to the um metal um metal upgrade on the front. Uh front split is really easy to just stuck that in between the um, the front bumper and then um just put two screws in it. Two screws in there put two holes in there and screwed it to the um plate there, the metal plate there um and that’s, pretty good, um and that’s it guys. I mean i just wanted to run through give you guys some idea what you can do with your original cell, i like the original cell um and i’m on a limited budget, so i just um start with a rash uh.
The shell original shell and i thought um, you know i’d use that so um problem we’re all having is with the electronics so, like i said, rear, pin, lift your the rear up, leave the front shot. You’Ll have enough to get your esc in get some side skirts on it. They’Re pretty easy to do. Uh just give you guys some ideas of what i did and um yeah. Overall, it just widens out the overall uh bottom of your uh bottom plate. Your metal plate try and keep show skirts. As you can see, i attached them to um the plastic, see the plastic that runs on the side. I attached them to that, so basically attach them to that, not the actual body, but attach them to that pretty easy to do. And then this is just wedged in between, as you can see, the screws are there wedged in between the bumper a little lip uh made out of plastic, basically, which will help you know when you’re doing a speed run, it’ll help uh suck the um, keep the Suction down on the um, the downfalls down and uh, you know help your body and also i’ve dropped the front so see the screws there put your screws in and drop the front. That’Ll help you out a lot. Uh dropping the front and the suspension get your suspension screwed down on both ends: um and that’s. It guys uh i’m waiting on uh parts to do a quick speed.
A few speed runs and just run this with this it’s um i’m. Just waiting on parts at the moment so um, but i have done a quick speed, run and uh. I haven’t used the gps, but just a quick run outside in the car park. If you want to check that out, that’s i’ve just put that up a couple of days ago um. But this is purely on uh, the body of the one four four zero zero one and what you can do you know cheap mods that you could do at home if you got the spare time you know like i said all this is just cut out: plastic. Um just cut out the plastic at the front, put the side skirts on and um a rear, rear body pin, which will lift up the rear, keep the front stock, and then you can get your esc and your brushless system in um. I know a lot of people going with the patch shells, but uh i do like the stock shell um. I like the look of it um, as i said, used a bit of um a bit: reinforced uh, reinforced uh rear wing with some uh carbon fiber tape. That’S, all that is and painted the shell back um and i just thought i’ll put it on the channel um, give you guys some ideas out there. You know what you, what you could do on a limited budget on your body shell and give it a few upgrades led lights model lights there uh running off a pill battery at the back, so just cut that out put it.
I can just put a pill battery in there when i want uh when i want the lights on or when i would use them in the evening and uh that’s it guys, so i hope you enjoyed watching. I hope this is giving you a few ideas on what you can do with your body show if you’re having trouble uh fitting your electrolytics in um for the price of a pin and just raising up the back to a roughly about this height. You know where this uh rear metal bracket is and and you’ll be.