We do essential upgrades and modifications on the double l toys. 一二: 四: 零一: nine stay tuned, 音乐, 好吧, so the first thing we’re going to start off with is the shocks so we’re going to be replacing the fluid with 37.5 weights fluid, and this is mostly because the little toys for whatever reason tend to Overfill or underfill the shocks it’s like you can see this one’s rock hard and this one’s a bit not that much so that’s. What we’re going to start off with all right, so we’ve got the shocks off. I am going to show you one on camera and the rest once we’re gon na go off camera yeah, so we’re gon na start off with disassembling and cleaning it up a little bit, because they’ve been dirty from being outside. Put that Music Music. Definitely another best thing to do on aluminium but that’s. What i’m going to use anyway, i’m going to start off with putting the bag there. So i can just all right when i do assemble these again i’m, going to be putting a little bit of oil in the ball joints, because this stuff will dry out or whatever’s in there if there’s anything in there. 所以希望, that will do a little bit of a difference. Looks really nice and shiny, they’re nice to be such a cheap car, as this is uh, the quality actually seems more than i expected plot this little pink wrench, Music and loosen off a bit by hand.
好吧, let’s have a look in there yep, so the bladder and everything came out. This is one of the ones really hard. So in the end i’m, just gon na drain the fluid out take one of these cups one. Before put it like that, hang it up in there and then you wait a few minutes, maybe five. So a short notice that i’ve run into is the fact that every cap head has been severely tied. 嗯, the bottom one has been normally halfway off. Have a look at that if you drew around so one of the signs that your wl toys one two four zero one, nine with the shocks being overfilled, is that you can’t compress them fully this one doesn’t go further than that which is kind of bad. So this is definitely overfilled so i’m. Definitely adjusting these up Music, alright guys. So we got to the point: we’re disassembled, 我们, cleaned out so it’s time to fill it up. Just pour it in like that, and then you exercise piston a little bit making sure there’s. No air in there so let’s say have a look at this. I don’t know how well you can see it it’s filthy. This is what came out: 它, really bad it’s, dirty as hell but yeah. This is what we need to do. We need to fill them up and sort of get this too. It was built everywhere, 音乐, all right so i’m, going to do the exercising for the rest of these ones off camera i’ll be right, back gopro, stop, recording Music, all right so, 基本上, where you next is to attach the bladder back on, attach a little bone joint And then the gap on top of that, what you want to see is that when you tighten this up, you can still fully compress it like that, and it’s got a little bit of rebound that’s pretty much perfect as far as i’m concerned Music spring back on.
I might just adjust that up because that will have to be adjusted outwards to sort of what you want really spring tension. And when you do this, you got ta ensure that, 是的, those things that i had shown you that i thought was an issue was what kind of that little thing little bottom cap. If it is, then all good see perfect according to me all right. The next thing we’re going to adjust is towing in the rear because, 正如你所看到的, they’re quite pretty much angled inward, so you’ve got to put a bad toe in. If you want to do speed runs. This is a bad thing. If you want to do track racing or whatever it’s pretty good as it is so what i’m going to do is to flip these little bushings in the back over and that will move the arm a little bit straighter all right. So next up is the droop screws. 所以, 正如你所看到的, there’s a bit of a difference here, so this is without a screw, and this is with a screw something that i do recommend this. 所以这是, i am using an m3 screw um. I don’t know maybe 12 long ones. I recommend to use washers to create the distance that you want to make sure you can bottom the screws out into the plastic to make sure they don’t unscrew um. I haven’t done that as of yet here, but that’s what’s going to happen right here now, 好吧, 是的, so let’s have a look so i’ve set the group in the front, 正如你所看到的.
Hopefully i don’t know how well this presents. I’Ve used a slightly thicker washer and a shorter screw in the front and a longer screw with a small washer in the back and i’m hoping that this will go pretty alright. 正如你所看到的, it moves fairly well um compared to before, like when they did. The shocks didn’t move at all and the droop was just really bad. 好吧, it’s all be a little bit hard to see, but i’ve adjusted the length of this rod right here and this right right there and for the toe, and i adjusted the steering, links right here and right there. So you’ll need something small. I had my 1.5 mil screwdriver from src and it just fitted straight in yeah, so that’s what i used to adjust it. I don’t know if i’m gon na have to do it in the back too, but as for right now, i think this is gon na.